Timeworks clock parts pendulum install#
Timeworks clock parts pendulum plus#
Timeworks clock parts pendulum free#

When working on a quartz clock movement measurement the post has to be long enough to go through whatever thickness that the clock face/dial, might be. This applies to all Clockworks quartz movements, including chiming quartz, and time only quartz movements. To clarify, the post is the part that goes through the dial (face) and mounts from the front and what is in a quartz clock movement measurement. This is so it can match up with the new quartz movement. When completing a quartz clock movement measurement, you will need to measure the post on the old movement. Altogether, these are the assembly instructions for the time only quartz clock movement into the clock case.Ĭlockworks offers multiple post lengths for quartz movements. Likewise, Quartz clock movement installation is usually very easy. Now it is out of the way and installation of the new quartz clock movement bought from Clockworks can be done. So, if this is the case, very gently pry the movement off of the back of the clock with a screwdriver. On occasion, the movement will have glue holding it in place. In essence, the movement will fall out the back of the clock dial. Then remove the hex nut that is on the post where the hands were. Every clock is different so thoroughly look your clock over to see how it was put together. Some clocks will have a glass bezel that will have to be taken off in order to get to the hands. Of course, this is done by removing the hands from the clock. Sometimes this is straightforward and sometimes it can be tricky. The first step is to get the old unit out of the way. This assembly gets brought back up again to mount with the set screw like it was.In essence, this is a quick step by step practical guide for the quartz clock movement installation. The leader then goes onto the suspension and the crutch on the back of the movement at the same time.

Timeworks clock parts pendulum free#

With the suspension free it can hook onto the leader and be brought back up.

Timeworks clock parts pendulum install#

To install the leader, remove the set screw on top of the suspension spring. The crutch is the wig wag part that is sticking out of the back of the movement. At the same time it will have the crutch on the back of the movement engaged with the center of the leader. The leader hangs onto the suspension spring which is on top of the movement. The leader is the 3 to 7 inch long part that the mechanical clock pendulum hangs onto. It may or may not need a new top hook for the pendulum. Sometimes an old pendulum will not hook to the new movement the same way as it did on the old unit. The leader is the part that holds the mechanical clock pendulum up in the air and it hooks to the suspension spring. The top hook has to hook to the leader on the movement. It only has to do with the pendulum length alone and nothing else. When a clock is too fast or slow it usually has nothing to do with the movement itself. If the pendulum is too short the clock will run too fast. If the mechanical clock pendulum is too long the clock will be too slow. The length of the pendulum has to be correct for the gearing inside the movement.

Timeworks clock parts pendulum plus#

Plus it is quite annoying to hear that sound! Pendulum lengths for Mechanical Clock Pendulum Assembly Eventually the clock will stop running from this resistance. If this rule did not exist and the 10 inch wide bob is run the clock may go tick, knock, tock, knock, as it hits the sides every time it swings. So the choice is clear that for a 12 inch wide clock case the maximum bob size to get is 8 1/2 inches wide. In this example we would need a 10 inch bob but these are not made.

So if the clock case is 12 inches wide the bob cannot be more than 10 inches. A good rule for the bob diameter is it needs two inches on each side to swing. To determine the bob diameter for a mechanical clock pendulum, need to consider what looks good as well as which one won't whack the sides of the case. The pendulum could be a brass rod, wood stick, or metal lyre style. This is interesting because it explains why there can be so many variations in pendulums for one movement. A place such as Clockworks or Howard Miller instead of the movement manufacturer. Usually mechanical clock pendulum makers are not movement makers and the two are married together by a person or place. A pendulum assembly consists of the suspension spring at the top, the leader that hangs on it, and then the pendulum. The use of the word assembly means the pendulum consists of three components and not just the pendulum.

The mechanical clock pendulum assembly does not mean just the pendulum alone.